Manual watering is not the best long-term solution if you’re constructing a new house and wish to maintain your gardens with minimal maintenance or establish a new system to water your current gardens. In Perth’s hot environment, keeping a vibrant, bright, green lawn necessitates garden reticulation Perth installation for people who want it to appear beautiful but need more time. If you’re wondering how to install reticulation in Perth or whether you must hire an expert to do it for you, keep reading for advice in the lawn irrigation installation guide.
Table of Contents
Begin With a Plan
Assess and plan your yard, considering the existing garden trees, beds, and grass space. Include any obstructions, such as garden plants, fences, or trees, and as much information as possible when constructing your map. This entails sketching to scale. Additionally, ensure that the position of your manifold, or water connection point, is indicated.
When you provide them with a complete and sufficient design of the area, or when you bring it into their shop, they will label it on the paper where items must be put; some reticulation installation Perth components distributor could assist you in figuring out the numbers and kinds of components you require. If not, at the very least, you will have a clear idea of your area and what you should do.
Identify Your Flow Rate and Water Pressure
This is an important phase since you must identify the flow rate and the water pressure to determine the number of solenoids for sprinklers you require, how long your system must operate, and so on. For instance, the suggested quantity of water in one watering time for Perth sandy soil is 10mm since the usual watering rate for a sprinkler is around 35-45mm every hour, which implies you will require to run them for about 13-16 minutes to give back 10 mm of water to your grass.
However, those figures may fluctuate depending on the flow rate of your land and the kind of sprinklers you utilise since every form of sprinkler may conduct water at a variable rate.
● Getting Your Flow Rate
A flow test will give you a decent idea of how many sprinklers you could operate simultaneously. To achieve this, time how long it takes to serve a 9L bucket at full pressure from your tap in seconds.
● Getting Water Pressure
A pressure gauge is required to measure the water pressure on your property. These are available at most irrigation supply shops. Attach the gauge to your tap, open it, and check the findings.
To acquire a reasonable average, repeat this procedure for every tap, mainly when designing a system for your back and front gardens, which might vary. When doing the test, ensure that everyone in your home uses water. Following that, you could take it to your distributor along with your area plan, and they must be able to advise you on what you require to get started with your garden reticulation installation Perth.
Make Zones for Your Lawns
To prevent water waste, every zone must demand a similar quantity of water regularly. This step is critical to ensuring that you utilise only what is necessary, resulting in a large water bill or failing to water areas that require it, resulting in a patchy lawn. Lawn sprayers and drippers, for instance, cannot be placed in a similar zone, according to reticulation Perth specialists. This leads to consistent water coverage and efficient water consumption.
A standard guideline is to have at most 60 to 75 per cent of total pressure directly into your irrigation system. This is where solenoids or valves come in, allowing you to divide your system into zones, each with its own valve to water various lawn areas multiple times. When you need clarification about the number of zones you require, you should get assistance from a specialist.
Understand Your Soil Type
Sandy soil needs tighter spacing because water opts to drain through it, but clay soil necessitates wider spacing because water tends to move laterally more on clay. A dripline run must be installed every 30 cm as a general rule to form a grid pattern with a dripper at every corner. When you need clarification on what you require, consult with a lawn irrigation consultant.
Automated or a Manual System
Manual irrigation systems are the less expensive first alternative, particularly when you have begun to shop around and receive estimates. A fully automatic reticulation system, in which your gardens are hydrated whether you’re at your house or not, necessitates more effort and initial expenses. This system will require a multi-core cable, solenoid valves, and a controller, as well as the services of an electrician when your controller is to be hardwired rather than just plugged in.
In addition, an automatic garden Perth reticulation system will also spare you time, keep your grass irrigated and healthy even while you are away, and simplify your life.
Select a Reticulation Controller
A reticulation controller-controlled automatic lawn watering system is always suggested. This allows you to guarantee that your lawn is watered on the correct days and hours, whether at home or not. A tap timer is a low-cost alternative that eliminates the need to stand there with a hose but still demands more attention and time. Also, occasionally the faucet is unintentionally turned off, and you only realise when your grass looks dry and brown that it is sometimes too late to preserve it.
In Summary
Reticulation Perth is advantageous, particularly when you like to keep your grass well-watered and maintained. However, establishing a lawn reticulation system for the first time might be difficult because of the many elements to consider. An experienced professional can help you with anything from reticulation system layout and installation to system overhauls, additions, and updates.
